FESTO Cambelt axle 8083669 ELGS-TB-KF-45-800-ST-M-H1-PLK-AA 53 A
Additional technical information: Protection class: IP40Ambient temperature: 0 °C - +50 °CProduct weight: 3,630 gLED displayStorage temperature: -20 °C to +60 °C.Relative humidity: 0 - 90 %Approval: RCM MarkNote on ambient temperature: Above the ambient temperature of 30 °C, a power reduction of 2 % per K must be observed.Temperature monitoring: Switch-off in case of overtemperatureIntegrated precise CMOS temperature sensor with analogueue outputMounting position: HorizontalVibration resistance: Transport application test with sharpening degree 1 according to FN 942017-4 and EN 60068-2-6Shock resistance: Shock test with sharpness 1 according to FN 942017-5 and EN 60068-2-27Rotor position sensor: Encoder absolutely single turnRotor position sensor measuring principle: MagneticRotor position sensor resolution: 16 bitsProtection class IIIPermissible voltage fluctuations: +/- 15 %Number of digital logic inputs: 2Switching logic inputs: PNP (positive switching)Properties of logic input: Configurable, not electrically isolatedSpecification of logic input: In accordance with IEC 61131-2, type 1Operating range logic input 24 VNumber of digital logic outputs 24 V DC: 2Switching logic outputs: PNP (positive switching)Properties of digital logic outputs: Configurable, not electrically isolatedMax current digital logic outputs: 100 mASize: 45Design: Electromechanical linear axis, with toothed belt, with integrated driveRepeat accuracy ±0.1 mmPosition detection: Motor encoder, for proximity switchesDuty cycle: 1Power supply, connection type: PlugPower supply, connection method: M12x1, T-coded according to EN 61076-2-111Power supply, number of poles/wires: 4Logic interface, connection type: PlugLogic interface, connection technology: M12x1, A-coded according to EN 61076-2-101Logic interface, number of poles/cores: 8Logic interface, connection diagram: 992264Max. Cable length: 15 m outputs, 15 m inputs, 20 m with IO-Link operationMax current consumption: 5.3 AIO-Link, SIO mode Support: YesIO-Link, protocol: Device V 1.1IO-Link, communication mode: COM3 (230.4 kBaud)IO-Link, port type: A.IO-Link, number of ports: 1IO-Link, process data width OUT: 2 bytesIO-Link, process data content OUT: 1 bit (Move in), 1 bit (Move out), 1 bit (Quit Error)IO-Link, process data width IN: 2 bytesIO-Link, process data content IN: 1 bit (state device), 1 bit (state move), 1 bit (state in), 1 bit (state out)IO-Link, service data content IN: 32 bit force, 32 bit position, 32 bit speedIO-Link, minimum cycle time: 1 msIO-Link, data storage required: 0.5 kilobytesIO-Link, connection pin: PlugParameterization interface: IO-Link, user interfaceInsulation protection class: BMotor type: Stepper motorReferencing: Fixed stop block positive, fixed stop block negativeAdditional functions: User interface, integrated end position detectionOperational readiness display: LEDKC-MARK: KC-EMCDrive pinion effective diameter: 19.1 mmWorking stroke 800 mm.Toothed belt elongation: 0.187 %Toothed belt division: 2 mmGuide: Ball circulation guideMax. Acceleration 6 m/s2Max. speed 1.2 m/sSurface torques 2. Grades Iy: 140 * 1003 mm4Surface torques 2. Grade Iz: 170 * 1003 mm4Max. Force Fy: 300 N.Max. Force Fz: 600 N.Max. Feed force Fx 75 N.Guide value payload, horizontal: 2.5 kgFeed constant 60 mm/revMaterial profile: Aluminum wrought alloy, anodizedDrive cover material: Die-cast aluminum, paintedMaterial pulleys: High-alloy steel, stainlessSlide material: Die-cast aluminumMaterial toothed belt: Polychloroprene with glass fiberHubreserve: 0 mmMax. Torque MX 5.5 NmMax. Torque My: 4.7 NmMax. Torque MZ: 4.7 NmMoving mass at 0 mm stroke: 169 gMaterial guide carriage: Heat-treated steelMaterial guide rail: Quenched steelTorsion moment of inertia IT: 8.5 * 1003 mm4Moving mass: 169 gWeight of carriage 55 gMaterial end cover: Die-cast aluminum, paintedMaterial masking tape: Stainless steel; Nominal current: 5.3 A; Nominal voltage: 24 V